|
|
| Line 3: |
Line 3: |
| | | | |
| | | | |
| − | back to [[IACL:CEREBELLUM_Protocol|Protocol for Cerebellum Delineation]]
| + | <Protocol not yet public> |
| − | | |
| − | | |
| − | == Outline ==
| |
| − | * Begin with an MRI image and completed Phase 1 (Whole Cerebellum) mask.
| |
| − | * Lock the background by changing its value to an unused paint value.
| |
| − | * Paint the corpus, and then lock it.
| |
| − | * Delineate Lobules I-V, VI-VII, and VIII-X by locating and following fissures (Primary and Prebiventer).
| |
| − | * Common obstacles and solutions
| |
| − | | |
| − | == Locking the Background ==
| |
| − | | |
| − | With the phase 1 mask loaded, the first thing that must be done is to lock the background layer. This layer includes anything that is NOT cerebellum and will serve as a guideline to minimize errors. First, go to Utilities -> Replace Pixel/Voxel Value. You will presented with a window similar to the figure below. In the box labeled "User defined value(s) and/or range(s)", type the number 0. Underneath the label "Replace with", type in a number that corresponds to a mask layer you will not use in the future. I recommend 19 simply because I think it has the best contrast with the other colors. Finally, select the option "Replace image" and click OK. The paint will need to be refreshed to be displayed properly.
| |
| − | | |
| − | [[Image:Lockback.PNG| 322 px| Locking Background]]
| |
| − | | |
| − | Next, proceed to the advanced paint tools window that you loaded the phase 1 mask with. Click the button that says "Show label text". Find the number that you replaced the background with and click the lock symbol next to it. The final result should look like this:
| |
| − | | |
| − | [[Image:Painttools.PNG| 400px| Locked!]]
| |
| − | | |
| − | It may be useful to reduce the opacity of the background paint by adjusting the "Active Image and Alpha Blending" bar to roughly .75A.
| |
| − | | |
| − | When the Corpus Medullare and Lobes have been labeled, change the background back to the "zero" label
| |
| − | | |
| − | == Painting the Corpus Medullare ==
| |
| − | For the delineation of the CM, sagittal view is recommended. Select layer 2 and pick a small to medium paintbrush (3x3 and 4x4 recommended) to begin painting in the corpus. If necessary, adjust the Active Image and Alpha Blending to increase the transparency of the other colors. To define the edges of the corpus, simply take lowest point between the valleys of the gray matter and visualize an imaginary line between them. This process is clarified in following figure (The red dots show where the valleys are):
| |
| − | | |
| − | [[Image:Corpusbound.PNG|Boundary between corpus and the rest of the cerebellum]]
| |
| − | | |
| − | IMPORTANT: Always keep in mind that a smooth and logical boundary is more important than an "accurate" boundary. Always double check with axial and coronal views to make sure the boundary is as smooth as possible
| |
| − | | |
| − | == Locating Fissures ==
| |
| − | | |
| − | The primary fissure (indicated by the red line) separates Lobules V and VI as shown below:
| |
| − | | |
| − | [[Image:primary.PNG|Primary Fissure]]
| |
| − | | |
| − | | |
| − | The prebiventer fissure separates Lobules VII and VIII as shown below:
| |
| − | | |
| − | [[Image:prepyramidal.PNG|Prebiventer/Prepyramidal Fissure]]
| |
| − | | |
| − | == Following Fissures ==
| |
| − | The easiest way to follow a fissure is to start at the midline slides and progress to the outer edges of the cerebellum. Once a fissure is located, the fastest way to outline the fissure is to paint lobules VI and VII (Posterior Lobe). This means that both the fissures will be defined at the border of the posterior lobe. After that is done, the posterior lobe can simply be locked, thereby making painting I-V and VIII-X trival.
| |
| − | | |
| − | == Common Obstacles and Their Solutions ==
| |
| − | There are a lot of obstacles.
| |
